I just downloaded and install "Version 1.5.0-SVN-33559 (SVN Rev 33559 from
/trunk)" but I still cannot read the trace, there is no change in behavior.
Someone else tried to read the trace with a 1.2 version of wireshark and had
no problems, it appears to be an issue with version 1.4 (and it appears
later).
How do I upload a binary trace as an example?
Noah Davids
=+=+=+=+=+=+=+=+=+=+=+=+=+=+
Serendipity is a function of bandwidth
If you are not the intended recipient of this E-mail it would be nice if you
deleted it and notified me that you received it incorrectly. On the other
hand, E-mail in an insecure mechanism; nothing in this E-mail can be
considered confidential. I have no doubts that copies of this E-mail have
been archived by my ISP, your ISP and probably the FBI, CIA and NSA. I
suspect that Interpol, MI-6, SVR (think KGB) and MSS (Chinese) will have
copies shortly, the NSIS (Kenya) will have it by the end of the week.
Message: 2
Date: Mon, 19 Jul 2010 09:02:01 -0700
From: "noah davids" <ndav1@xxxxxxx>
Subject: [Wireshark-users] network monitor 3.3 traces cannot be read
To: <wireshark-users@xxxxxxxxxxxxx>
Message-ID: <5AE6243C91B5411FB04F45D5E8FDF4C3@noahdesk>
Content-Type: text/plain; charset="iso-8859-1"
I just tried to read a trace created with Microsoft Network Monitor
version 3.3 using Wireshark version 1.4. All the frames have a Protocol of
UNKNOWN and Info of "WTAP_ENCAP = 0". The first two frames appear to be
Unicode text but starting with frame 3 the hex dump shows it to be an IP
packet.
"Decode As" is grayed out so I can't even force a decode. Any idea how I
can read this trace?
Noah Davids
Message: 4
Date: Mon, 19 Jul 2010 19:24:28 +0200
From: Stig Bj?rlykke <stig@xxxxxxxxxxxxx>
Subject: Re: [Wireshark-users] network monitor 3.3 traces cannot be
read
To: Community support list for Wireshark
<wireshark-users@xxxxxxxxxxxxx>
Message-ID:
<AANLkTimG4wsN2bN634xeJmHE97eH0Kje9cO2X43iYY4z@xxxxxxxxxxxxxx>
Content-Type: text/plain; charset=ISO-8859-1
On Mon, Jul 19, 2010 at 6:02 PM, noah davids <ndav1@xxxxxxx> wrote:
Any idea how I can read this trace?
Sure, try the latest build from the buildbot:
http://www.wireshark.org/download/automated/
--
Stig Bj?rlykke
------------------------------
Message: 5
Date: Mon, 19 Jul 2010 12:25:41 -0500
From: "DePriest, Jason R." <jrdepriest@xxxxxxxxx>
Subject: Re: [Wireshark-users] network monitor 3.3 traces cannot be
read
To: Community support list for Wireshark
<wireshark-users@xxxxxxxxxxxxx>
Message-ID:
<AANLkTikZqXDzMayMuHZ2tiA8Cm2w0PBsJbqsQiplTf0y@xxxxxxxxxxxxxx>
Content-Type: text/plain; charset=ISO-8859-1
Hello,
Can you send an example capture to the list?
I just captured about 30 seconds of traffic using Microsoft Network
Monitor 3.3 and saved it in its default .cap format. I was able to
open it in Wireshark 1.2.9 without any problems.
-Jason
