Wireshark · Wireshark-dev: Re: [Wireshark-dev] QT DLLs missing from build environment

[Paul Offord <Paul.Offord@xxxxxxxxxxxx>]

I did the following:

 

·        Deleted the QT5.5.1 directory

·        Installed Qt5.6.1

·        Deleted my wsbuild64 directory content

·        Ran the cmake build prep step

·        Opened the Wireshark.sln in VS 2013

·        Set Wireshark as the Startup Project

·        Ran a Build for Debug x64

·        Clicked on Local Windows Debugger to start Wireshark

·        Wireshark started successfully

·        Checked the Run\Debug directory and the QT5 DLLs are all in there

 

Thanks for the help.

 

Best regards…Paul

 

From: Paul Offord
Sent: 27 December 2016 14:12
To: Developer support list for Wireshark <wireshark-dev@xxxxxxxxxxxxx>
Subject: Re: [Wireshark-dev] QT DLLs missing from build environment

 

Hi Anders,

 

I plan to upgrade Qt but I thought I'd try a build with releases I've used before.  I notice that the Qt site is offering 5.7 - is that a supported release?

 

Thanks...Paul

 

 

Sent from Samsung Mobile on O2

 

-------- Original message --------

From: Anders Broman

Date:27/12/2016 14:04 (GMT+00:00)

To: Developer support list for Wireshark

Subject: Re: [Wireshark-dev] QT DLLs missing from build environment

 

Hi,

At some point I think there was a fault in Qt causing it to not copy all .dll when running the command to do so. I’m currently building with Qt 5.6 which I believe is supposed

To be LTS.

Regards

Anders

 

From: wireshark-dev-bounces@xxxxxxxxxxxxx [mailto:wireshark-dev-bounces@xxxxxxxxxxxxx] On Behalf Of Paul Offord
Sent: den 27 december 2016 14:05
To: Developer support list for Wireshark <wireshark-dev@xxxxxxxxxxxxx>
Subject: [Wireshark-dev] QT DLLs missing from build environment

 

I’m building the latest Wireshark source on Windows 7 with QT5.5.1 and VS 2013.  As you may have seen from earlier posts, I scratched my old build environment and I’m creating a new one.  The build prep and build (Debug) complete successfully, but when I try to start Wireshark I get a message saying Qt5PrintSupportd.dll can’t be found.

 

I remember this from when I created the environment last time around, and I fixed it by copying the DLLs required into the Wireshark run directory.  I guess this isn’t the way I should be doing it.  What’s the correct procedure here?

 

Thanks and regards…Paul

 

______________________________________________________________________

This message contains confidential information and is intended only for the individual named. If you are not the named addressee you should not disseminate, distribute or copy this e-mail. Please notify the sender immediately by e-mail if you have received this e-mail by mistake and delete this e-mail from your system.

Any views or opinions expressed are solely those of the author and do not necessarily represent those of Advance Seven Ltd. E-mail transmission cannot be guaranteed to be secure or error-free as information could be intercepted, corrupted, lost, destroyed, arrive late or incomplete, or contain viruses. The sender therefore does not accept liability for any errors or omissions in the contents of this message, which arise as a result of e-mail transmission.

Advance Seven Ltd. Registered in England & Wales numbered 2373877 at Endeavour House, Coopers End Lane, Stansted, Essex CM24 1SJ

______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please visit http://www.symanteccloud.com
______________________________________________________________________

______________________________________________________________________

This message contains confidential information and is intended only for the individual named. If you are not the named addressee you should not disseminate, distribute or copy this e-mail. Please notify the sender immediately by e-mail if you have received this e-mail by mistake and delete this e-mail from your system.

Any views or opinions expressed are solely those of the author and do not necessarily represent those of Advance Seven Ltd. E-mail transmission cannot be guaranteed to be secure or error-free as information could be intercepted, corrupted, lost, destroyed, arrive late or incomplete, or contain viruses. The sender therefore does not accept liability for any errors or omissions in the contents of this message, which arise as a result of e-mail transmission.

Advance Seven Ltd. Registered in England & Wales numbered 2373877 at Endeavour House, Coopers End Lane, Stansted, Essex CM24 1SJ

______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please visit http://www.symanteccloud.com
______________________________________________________________________